GI Probes

Introduction

Just like with Reflection Probes, and as stated in the Spatial Material, objects can show reflected or diffuse light. GI Probes are similar to Reflection Probes, but they use a different and more complex technique to produce indirect light and reflections.

The strength of GI Probes are real-time, high quality, indirect light. While the scene needs a quick pre-bake for the static objects that will be used, lights can be added, changed or removed and this will be updated in real-time. Dynamic objects that move within one of these probes will also receive indirect lighting from the scene automatically.

Just like with ReflectionProbe, GIProbes can be blended (in a bit more limited way), so it is possible to provide full real-time lighting for a stage without having to resort to lightmaps.

The main downside of GIProbes are:

  • A small amount of light leaking can occur if the level is not carefully designed. this must be artist-tweaked.
  • Performance requirements are higher than for lightmaps, so it may not run properly in low end integrated GPUs (may need to reduce resolution).
  • Reflections are voxelized, so they don’t look as sharp as with ReflectionProbe, but in exchange they are volumetric so any room size or shape works for them. Mixing them with Screen Space Reflection also works very well.
  • They consume considerably more video memory than Reflection Probes, so they must be used by care in the right subdivision sizes.

Setting Up

Just like a ReflectionProbe, simply set up the GIProbe by wrapping it around the geometry that will be affected.

../../../_images/giprobe_wrap.png

Afterwards, make sure to enable the geometry will be baked. This is important in order for GIPRobe to recognize objects, otherwise they will be ignored:

../../../_images/giprobe_bake_property.png

Once the geometry is set-up, push the Bake button that appears on the 3D editor toolbar to begin the pre-baking process:

../../../_images/giprobe_bake.png

Adding Lights

Unless there are materials with emission, GIProbe does nothing by default. Lights need to be added to the scene to have an effect.

The effect of indirect light can be viewed quickly (it is recommended you turn off all ambient/sky lighting to tweak this, though as in the picture):

../../../_images/giprobe_indirect.png

In some situations, though, indirect light may be too weak. Lights have an indirect multiplier to tweak this:

../../../_images/giprobe_light_indirect.png

And, as GIPRobe lighting updates in real-time, this effect is immediate:

../../../_images/giprobe_indirect_energy_result.png

Reflections

For materials with high metalness and low roughness, it’s possible to appreciate voxel reflections. Keep in mind that these have far less detail than Reflection Probes or Screen Space Reflections, but fully reflect volumetrically.

../../../_images/giprobe_voxel_reflections.png

GIProbes can easily be mixed with Reflection Probes and Screen Space Reflections, as a full 3-stage fallback-chain. This allows to have precise reflections where needed:

../../../_images/giprobe_ref_blending.png

Interior vs Exterior

GI Probes normally allow mixing with lighting from the sky. This can be disabled when turning on the Interior setting.

../../../_images/giprobe_interior_setting.png

The difference becomes clear in the image below, where light from the sky goes from spreading inside to being ignored.

../../../_images/giprobe_interior.png

As complex buildings may mix interiors with exteriors, combining GIProbes for both parts works very well.

Tweaking

GI Probes support a few parameters for tweaking:

../../../_images/giprobe_tweaking.png
  • Subdiv Subdivision used for the probe. The default (128) is generally good for small to medium size areas. Bigger subdivisions use more memory.
  • Extents Size of the probe, can be tweaked from the gizmo.
  • Dynamic Range Maximum light energy the probe can absorb. Higher values allow brighter light, but with less color detail.
  • Energy Multiplier for all the probe. Can be used to make the indirect light brighter (although it’s better to tweak this from the light itself).
  • Propagation How much light propagates through the probe internally.
  • Bias Value used to avoid self-occlusion when doing voxel cone tracing, should generally be above 1.0 (1==voxel size).
  • Normal Bias Alternative type of bias useful for some scenes. Experiment with this one if regular bias does not work.

Quality

GIProbes are quite demanding. It is possible to use lower quality voxel cone tracing in exchange of more performance.

../../../_images/giprobe_quality.png