This tutorial is a short and practical introduction to linear algebra as it applies to game development. Linear algebra is the study of vectors and their uses. Vectors have many applications in both 2D and 3D development and Godot uses them extensively. Developing a good understanding of vector math is essential to becoming a strong game developer.
This tutorial is not a formal textbook on linear algebra. We will only be looking at how it is applied to game development. For a broader look at the mathematics, see https://www.khanacademy.org/math/linear-algebra
Coordinate systems (2D)¶
In 2D space, coordinates are defined using a horizontal axis (
a vertical axis (
y). A particular position in 2D space is written
as a pair of values such as
If you’re new to computer graphics, it might seem odd that the
y axis points downwards instead of upwards,
as you probably learned in math class. However, this is common
in most computer graphics applications.
Any position in the 2D plane can be identified by a pair of numbers in this
way. However, we can also think of the position
(4, 3) as an offset
(0, 0) point, or origin. Draw an arrow pointing from
the origin to the point:
This is a vector. A vector represents a lot of useful information. As
well as telling us that the point is at
(4, 3), we can also think of
it as an angle
θ and a length (or magnitude)
m. In this case, the
arrow is a position vector - it denotes a position in space, relative
to the origin.
A very important point to consider about vectors is that they only represent relative direction and magnitude. There is no concept of a vector’s position. The following two vectors are identical:
Both vectors represent a point 4 units to the right and 3 units below some starting point. It does not matter where on the plane you draw the vector, it always represents a relative direction and magnitude.
You can use either method (x and y coordinates or angle and magnitude) to
refer to a vector, but for convenience, programmers typically use the
coordinate notation. For example, in Godot, the origin is the top-left
corner of the screen, so to place a 2D node named
Node2D 400 pixels to the right and
300 pixels down, use the following code:
Godot supports both Vector2 and Vector3 for 2D and 3D usage, respectively. The same mathematical rules discussed in this article apply to both types.
The individual components of the vector can be accessed directly by name.
When adding or subtracting two vectors, the corresponding components are added:
We can also see this visually by adding the second vector at the end of the first:
Note that adding
a + b gives the same result as
b + a.
Vectors represent both direction and magnitude. A value representing only magnitude is called a scalar.
A vector can be multiplied by a scalar:
Multiplying a vector by a scalar does not change its direction, only its magnitude. This is how you scale a vector.
Let’s look at two common uses for vector addition and subtraction.
A vector can represent any quantity with a magnitude and direction. Typical examples are: position, velocity, acceleration, and force. In
this image, the spaceship at step 1 has a position vector of
a velocity vector of
(2,1). The velocity vector represents how far the
ship moves each step. We can find the position for step 2 by adding
the velocity to the current position.
Velocity measures the change in position per unit of time. The new position is found by adding velocity to the previous position.
Pointing toward a target¶
In this scenario, you have a tank that wishes to point its turret at a robot. Subtracting the tank’s position from the robot’s position gives the vector pointing from the tank to the robot.
To find a vector pointing from
B - A.
A vector with magnitude of
1 is called a unit vector. They are
also sometimes referred to as direction vectors or normals. Unit
vectors are helpful when you need to keep track of a direction.
Normalizing a vector means reducing its length to
preserving its direction. This is done by dividing each of its components
by its magnitude:
Because this is such a common operation,
a method for normalizing:
Because normalization involves dividing by the vector’s length,
you cannot normalize a vector of length
0. Attempting to
do so will result in an error.
A common use of unit vectors is to indicate normals. Normal vectors are unit vectors aligned perpendicularly to a surface, defining its direction. They are commonly used for lighting, collisions, and other operations involving surfaces.
For example, imagine we have a moving ball that we want to bounce off a wall or other object:
The surface normal has a value of
(0, -1) because this is a horizontal
surface. When the ball collides, we take its remaining motion (the amount
left over when it hits the surface) and reflect it using the normal. In
Godot, the Vector2 class has a
to handle this. Here is a GDScript example of the diagram above using a
The dot product is one of the most important concepts in vector math, but is often misunderstood. Dot product is an operation on two vectors that returns a scalar. Unlike a vector, which contains both magnitude and direction, a scalar value has only magnitude.
The formula for dot product takes two common forms:
However, in most cases it is easiest to use the built-in method. Note that the order of the two vectors does not matter:
The dot product is most useful when used with unit vectors, making the
first formula reduce to just
cosθ. This means we can use the dot
product to tell us something about the angle between two vectors:
When using unit vectors, the result will always be between
We can use this fact to detect whether an object is facing toward another
object. In the diagram below, the player
P is trying to avoid the
B. Assuming a zombie’s field of view is 180°, can they see the player?
The green arrows
fB are unit vectors representing the
zombies” facing directions and the blue semicircle represents its field of
view. For zombie
A, we find the direction vector
AP pointing to
the player using
P - A and normalize it. If the angle between this
vector and the facing vector is less than 90°, then the zombie can see
In code it would look like this:
Like the dot product, the cross product is an operation on two vectors. However, the result of the cross product is a vector with a direction that is perpendicular to both. Its magnitude depends on their relative angle. If two vectors are parallel, the result of their cross product will be a null vector.
The cross product is calculated like this:
With Godot, you can use the built-in method:
In the cross product, order matters.
a.cross(b) does not
give the same result as
b.cross(a). The resulting vectors
point in opposite directions.
One common use of cross products is to find the surface normal of a plane
or surface in 3D space. If we have the triangle
ABC we can use vector
subtraction to find two edges
AC. Using the cross product,
AB x AC produces a vector perpendicular to both: the surface normal.
Here is a function to calculate a triangle’s normal:
Pointing to a target¶
In the dot product section above, we saw how it could be used to find the angle between two vectors. However, in 3D, this is not enough information. We also need to know what axis to rotate around. We can find that by calculating the cross product of the current facing direction and the target direction. The resulting perpendicular vector is the axis of rotation.